Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I have problem with using nrf_serial.h, I am receiving data from Ublox GPS, baud rate = 9600, no flow control as we dont have enough IO pins.
Device is nrf52840 with...
Hello, I'm trying to integrate an SPI slave into ble_app_beacon example. Power consumption of ble_app_beacon between advertising is up to 10 uA. But if I write a byte over...
Hello
I am modifying the example of mpu6050 of sdk v14 in sdk v17.
After build, it is printed that there is no path to the file as shown in the image below.
(The...
Hello We recently went to a test facility SGS, in San Diego, with our nrf9160 device trying to get a pre-cert scanning completed to find out if there are changes needed before...
Using SDK 15.3 and S132.
I'm having similar behavior to the thread below:
https://devzone.nordicsemi.com/f/nordic-q-a/12066/gap-disconnect-stops-app-timer
After disconnecting...
hi ...
how to update the advertisement packet .. I have seen many post regarding this ,I am not getting clear , anyone can share me the piece of code which will help me
I am trying to repeat the example in the tutorial: using board: nrf9160dk_nrf9160.
nRF Connect SDK Tutorial - Part 3 | NCS v1.3.0 --> 1.2 Walkthrough for BME280 - but gives...
Hello,
Our setup:
-nRF9160
- Zephyr OS
- Segger Embedded Studio for Arm (Nordic Edition)
- SDK v1.3
Questions
1) which are the differences between Zephyr functions...
I'm designing a product around the nRF52840 (PAN1780 module), and using the PWM to drive a piezo sounder (using 2 pins as Hbridge). When I start using BLE functions, I get...
Hey, Yesterday we decided to update SDK to 17.0.2. After this change our FreeRTOS stopped working. We started investigating where is the problem and we found that when vPortSetupTimerInterrupt...
Dear all,
I'm currently using nrf52840DK with SDK 17.00 and s140 softdevice. I'm trying to syncronize the dispatch of my data with connection interval (set to 7.5 ms). I...
Using: Windows 10, nRF Connect v3.5.0, SES v4.52, ncs v1.3.0, zephyr v2.3.0
I have a custom board based on the Thingy91 and the Asset Tracker application. There is also...
Hi,
In the new AzureIotHub library, subsys\net\lib\azure_iot_hub\src\azure_iot_hub.c
the logic for handling connection conditions in mqtt_evt_handler requires more error...
How is CRYPTOCELL_IRQHandler linked in a project using CC310? I have built ble_app_interactive and it links to the library routine. However I need to develop my own application...
The current state of my thingy 91 is it blinks blue and then red. nrf connect reports that it has not been provisionized or something similar.
The included sim card is registered...
