I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I am working on a project that utilizes the periodic advertisement feature. I have an nrf9160DK as a gateway to synchronize to multiple advertisers. I use the nrf9160...
Dear Members,
How can i keep the data no being cut ?
before using call back function ,
after using call back function :
function :
call back from main :
...
I didn't change nrf5340_cpuapp_common.dts, and I saw the macro definition of "i2c1" in "devicetree_unfixed.h," but I called device_get_binding (DT_LABEL (DT_NODELABEL (i2c1...
Hi,
I found that the startup of the modem (init and connect) is much faster after it has stored some initial information ( I think band-data and so on). This only happens...
Hi,
I have two nRF52 DK boards which i bought one is 2 years old and another 1 year old.. Past week both DK boards are failed to connect with the computers but the power...
We have the following setup:
- nRF52832 XXAA
- SDK 6.0
- S132
I have attempted to add a memory guard into the location preceding the application RAM data block start...
Despite following the procedure listed below, no text appears on the OLED display, despite the driver being able to communicate with the device.
I am using nRF Connect SDK...
I am looking to get some clarification on the QFN94 footprint of the nRF5340. There are four corner pads and they do not appear in the mechanical specifiications section 9...
Hi,
When looking at the reference schematics and reference layout of nRF5340 I notice that pins A25, B12, B26, G1, H2 and J31 are grounded:
Figure 1. Circuit configuration...
Hi, with my nrf9160 I need to send a gps location every 3 sec to azure, so I combined the agps and the azure iot hub sample. It's working pretty good but 10 sec as a periodic...
Hi, I doing PCBA prototype. And I found part number nRF5340-QKAA-R and NRF5340-QKAA-AB0-R7 in the website. In my understanding. The NRF5340-QKAA-AB is a sample engineering...
Hi,
I want to used NRF5340-DK for my BLE receiver evaluation I find LNA (NRF21540-DB) which is suitable to use with NRF5340-DK.
But I could not find this available in...
I am just beginning with the dev kit I bought in December. The box has a URL: nordicsemi.com/start52840dk
This is not helpful. The only thing I find there is a PDF - apparently...
