Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I am trying to change the radio Tx power in nRF5340. I'm using Zephyr HCI RPMsg for the network core. The datasheet says it should support up to 3dBm. However, the Zephyr...
In the soft device documentation (html) the message sequence diagram for Btle Stack Enable calls sd_ble_cfg_set twice with the same set of parameters. Is this a mistake? The...
Hi All,
I am developing a custom BLE profile for my current project and several of my characteristics are write/notify characteristics. I am finding that when I write...
Hi there,
I just started using Embedded Studio (v5.10d on Windows 10, nRF Connect SDK version 1.4) with nRF52840dongle and nRF5340 PDK. Here is what I did
1. Copied...
Hi, I am developing a new project in which I will use NRF52810. I read in the datasheet that it is possible to configure NRF52810 in LDO and DC / DC regulators mode. My application...
Hello:
Looking at the different demos (applications and samples) available for nRF9160, I noticed that some of them generate multiple hex files while others, only few...
Hi,
I have bootloader programmed in nrf52840. Using OTA I programmed one application region but that application stuck after bootup.
Now how to recover from this situation...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
getting error in running bootloader
Output/secure_bootloader_ble_s112_pca10040e Release/Obj/nrf_dfu_validation.o: in function `nrf_dfu_validation_init':
I have designed a custom board with the nRF52840 following the examples from the dev kit, dongle, and datasheet (circuit config 5). The board is similar to the dongle but...
