Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, I am working on a project for nRF9160 that is supposed to provide FOTA/DFU functionality for main application, modem and nRF52832 co-processor acting as SPI HCI slave...
Hi Nordic team,
I hope this message finds you well. I am currently working on developing applications for custom boards utilizing the nRF Connect SDK v2.4.0, with a particular...
Hi Nordic Team,
I am currently working on developing applications for custom boards using the nRF Connect SDK v2.6.0, specifically focusing on the nRF52840 microcontroller...
I have build a simple program to Interface my PDM (ICS 41351) Mic with my nRF52840 DK usnig nRF SDK on VS Code, although the program in build and flashed successfully I cant...
Hi all,
I've been trying to get the samples/sensor/lsm6dsl example working with the nrf52840-based Xiao BLE Sense and have had no luck.
I guess that it's due to the power...
I'm building my zephyr project for nRF5340, using west.
However, each time I change my code and re-build to try it, my PC (which is pretty recent) takes around 40-50s just...
We are utilizing the nrf5340 alongside the nrf7002 for Bluetooth Low Energy (BLE) and Wi-Fi communication between a wearable device and a host. The host is a laptop connected...
Hello Nordic Team!
I updated to version 5.0.0 of NRF Connect for Desktop and since then, when I try to program my development kit in VS Code, it can appear as connected...
Hello,
I wanted to evaluate the nRF53 platform with nrf connect SDK so I got new nRF7002DK board. I have following versions of all tools installed.
- nRF connect SDK ...
Hi,
after upgrading to NCS v2.7.0, I have some trouble with an increased sleep power consumption of our device when I use Zephyr's gpio-keys for the button input.
I was...
I want to edit the sample source (nRF5340 Audio) and program it on my own board. The connection is CIS. I am using NCS version 2.5.0.
I want to set the I2S clock as follows...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
I tried the following settings to output 12.288MHz I2S MCLK with nRF5340 Audio, but it did not work as expected.
The I2S settings I want to output are as follows.
MCLK...
I am currently writing sniffer firmware to the nRF52840 and am trying to check Thread communication using WireShark.
When I displayed the RSS, I got the value shown in the...
1. Hi i am utilizing nrf52840 sdk with ver 17.1.10 s140 and i have the central UART as main app from there we are calling bootloader
2. Before calling bootloader ble dfu...