I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
Hi,
I am trying to disconnect an Android smartphone from the nRF52840. After trying for some time we found out that the BLE stack of Android does not reliably closes a Bluetooth...
hi..folks
wish you happiee new year
i am using nrf52832 whille i tried to pair my device with my android , i am getting an error message " pairing rejected by nordic_uart...
Hi,
According to below thread, the advertising interval has a random 0 - 10 msec delta, so if the adv interval is 20 mses, if run it for long enough, will the result be...
Hi,
I would like to use the PDM interface for my application in nrf52840.
I configured the driver, and started using the SDK's API successfully.
Question 1:
During...
We want to achieve something like this -> We have several BLE peripherals with us and we are going to connect this peripherals to nrf9160 using nrf52 module and then send...
Hi,master
I want to learn DFU/bootloader, I am looking at the official source code, but my ability is too bad, I can't understand it at all. Is there any detailed information...
Hi
I read some threads about how to pair/read IKEA Trådfri.
I'm using nRF5840 dongle with the HEX code cli from SDK 17.0.0.
Using the terminal and send
bdb role...
I have both a NRF52840 (actually 2) and 2 dongles. I need to measure RSSI vs distance for a single link. I set up the RSSI viewer and it shows a blue or green bar for the...
