Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I am study nRFGo Gazell now and I got confused on timer period change in gzll_radio_isr_function().
Per my understanding the Gazell link layer modify timer period...
Using nRF connect SDK V1.0.0
File --> Open nrf connect SDK project
Tools --> Option --> nRF connect
Install all the packages described in "Getting started...
We are evaluating the feasibility of a device using nrf52840 which requires below peripherals:
3 x SPI: For MCU to MCU communication + high-speed data transfer from sensors...
Hi,
I am using nRF51822 controller. And I am using SPI peripheral to read 80 bytes of converted data from an ADC converter.
While reading spi data I realized that there...
Hi,
I have build a application based on the mqtt-simple-sample and successfully integrated TLS.
Now I wanted to measure the floor current in PSM. I did wait some minutes...
Folks,
I have a dev board PCA10040, which is running, I think, soft device s132. Additional load file is:
components/softdevice/s132/hex/s132_nrf52_6.1.1_softdevice.hex...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
