Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi All,
I am Using the NRF52840 DK Device for my application development
I want 2 UARTS for my application
I have used the example - nRF5_SDK_15.3.0_59ac345\examples...
I am currently developing a central device based on the NRF52832. I am able to discover and get handles to all the services and characteristics of interest on the peripheral...
Hello,
I wanted to know if I can use AT commands to communicate with nrf52840 DK.
If it is possible, do I need to have a separate firmware or is nordic sdk enough?
Hi, I am new to FreeRTOS and am planning to change to some of my code routines to FreeRTOS because my code has been expanding and in need of priorities interrupts. I face...
Hi,
I have modified the asset tracking application to work with my AWS IOT account, I have noticed that after several minutes, the broker stops responding (not getting PUBACK...
Hi,
I am experimenting with ENC28J60 and PCA10056. Following are my connections:
================= =================================== NRF52840 PCA10056 ENC28J60 (pin...
Hi
I tried to implement Eddystone example in nRF52810. it worked successfully. Then i tried to implement same in nRF52832 using pca10040. But it not working. I only changed...
Hi, I'm running the saddc_pca10056 peripheral example given in SDK v15.2.0.
The analogue pin A0 is connected to the signal line of an LM35 temperature sensor. When I measure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I am porting RTC example code as is into ble_app_blinky...
hi...
i want to advertise the multi link central example , i have added the advertising in code , now my central is advertising but when i tried to connect , i am getting...
I programmed a NRF52840 Dongle with the example light switch code having changed the channel to 14 which is what my coordinator is on.
I then programmed a NRF52840DK with...
Good day,
I program my nRF52-DK with BLE Eddystone example's pre-compiled hex:
\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_eddystone\hex\ble_app_eddystone_pca10040_s132...
my bootloader.hex is generated by "nRF5_SDK_14.2.0_17b948a\examples\dfu\bootloader_secure_ble\pca10040\arm5_no_packs", my app.hex is generated by a modified blinky example...
