Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hello,
Now i use NRF51822 DK with code in attachment to test app_timer hangs.
Fristly , you can press button 0 to start a 100ms app_timer, and we can see it through uart...
I am attempting to use Enhanced Shockburst/Gazell working with coded PHY, in order to achieve long range communications with very lower power consumption. I have searched...
Hello, I am experimenting with your nrf5SDKforMeshv310
I can compile and download the included examples.
Because I own a few Thingy 52, I wish to flash them as light_dimming_servers...
hi,
I am trying to add SPI (master) codes into the ble_app_uart.
My setting for SPI is as follows:
#define SPI1_ENABLED 1 // #define SPI_INSTANCE 1 /**< SPI instance...
Hi I am using nRF52832 board amd i am trying to debug ble_app_uart as Central.
BLE connection is established between this central application and the peripheral.
Opened...
i am using nrf24l01+ on arduino devices, one arduino device as master, and other arduino devices as slaves. I like master to broadcast a radio (dataToSend) toward all slaves...
nrf52832, keil with startups from sdk13
Initialization:
IntHandler:
With one event everything working well. Then I add another:
I need to measure SENT signal...
hi.... folks
i am using nrf52840 development kit , and i debugged the merged programs such as uart and twi program in it .does it will give the temperature data?
i am...
Hi all,
Please refer to the SDK version : nRF5_SDK_15.2.0_9412b96.
We need to use two uarts simultaneously for module & device respectively.
For example :
UARTE0 ...
We, I am using nRF 5 SDK v 14.2.0.
Power-off has occurred during program development. I can not identify the location, Functions that are not memory leak, buffer overflow...
Hi,
Now, I am using the nRF52840 to develop and do signal test. Can you share me some tool that can make the board enter the test mode?
Best regards
Simon
Hi:
PREJECT: nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hrs_freertos\pca10040\s132\arm5_no_packs
When TWI0 and GPIOTE are turned on at the same time, the...
I'm trying to get the AT commands sent in the asset_tracker example written out together with the other printk statements. I have tried adding this to the prj.conf: CONFIG_LOG...
I used the nrf52840 as the central device, use SDK15.0, scan then connect the peripheral toys.
sometimes i found the central can scanned some ble peripheral but can't connected...
