Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
I am a beginner in BLE systems. I am designing a board with a Nordic chip, and I have difficulties in designing an antenna... Can you look at my technical solution and correct...
Hello,
I have an application that I built for the nRF52832 using the peripheral uart example that uses Bluetooth. I am using NCS 2.7.0 I am using the following peripherals...
I'm working with NSIB (nRF Secure Immutable Bootloader) and trying to manually sign an application image that is built separately — without using SB_CONFIG_SECURE_BOOT_APPCORE...
I have a custom board that uses nrf52832 and I would like to add FOTA support using Bluetooth.
When I build the code using the nrf Connect inside VS code, it creates a DFU...
Hello guys good Morning,
I am currently studying the examples in the Nordic Dev Academy. I am in lesson 5 from the "NRF Connect SDK Fundamentals", and I managed to toggle...
Hi,
I'm attempting to restore my Thingy91x to communicate with my instance of nRF Cloud (I had removed the certificates previously to test out the connection to another...
Hi,
I am using a custom nRF52832 board with multiple ADC channel readings sequentially. I am trying to read thermistor (NTC) value on channel 7 and not getting accurate...
Hi community,
I'm using the following setup:
nRF5340DK
nRF Connect SDK v2.6.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in...
Hi,
My requirements are:
My essential need is a one-to-one connection between central and peripheral .
But when my central receives the specified command to start scanning...
Hello there, this is my first post here.
I'm facing a wall in my project development.
Here is the issue, so during start up of the NRF52832 I see a high current draw for...
Hello, I need your help about BLE channels. Currently, I use only the primary channel 38 for advertising data but, when the data are sent, I don't have the information of...
Hello,
I am currently working on connecting a Thingy:91x to a Cube Orange autopilot (Pixhawk 2.1) in order to receive telemetry data over UART using the MAVLink protocol...
We need a parter to develop the Thread terminal base on Nordice nRF52840, the project will be design in China and produce in Germany. Is there any reliable company could provide...
I noticed that through apply_old_config.h configuration values like NRFX_CLOCK_ENABLED in sdk_config.h simply get overriden by the old CLOCK_ENABLED, so that there is no point...
