I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I am doing development on Android platform. I am using Marshmallow device to develop my BLE application. Many times I am getting status code 129 in onServicesDiscovered...
Hi, i'm working on a custom board with microswitch (Crouzet V4) in order to get the position of a moving part inside a machine. This switch is in pullup mode with a 100k resistor...
Hello,
I am using nrf51 and sdk12.2. I want to print data to terminal using printf function. So I added app_uart_fifo.c also I included paths. I did not get any errors from...
I'm using NRF51422, s130, SDK v12.
And I'm working on a project that can connect concurrent peripheral and Central.
In this continuious connect and disconnect sequences...
Hello,
I am using the bootloader_secure-Example on a custom-board and I want to configure a LED as status-indication.
Since I am on a custom-board I disabled the functions...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
Hello,
in my test I executed sd_mutex_acquire twice in sequence without releasing it. However, I did not get a "NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN" on the second time. What...
Hello,
I am using nrf51 and sdk11. I am trying to add twi drivers to code. I have added and also added path for the twi drivers. But I am getting error as "............\components...
Hello, I can program properly (the "--verify" command passed) my softdevice s140 into the chip, using nrfjprog 9.x. But now I can't use my keil uv5 to program my user app...
Good morning,
Based on different articles, I set up a nrf52832 with S132 3.1.0, the secure bootloader found in "SDK_12.2.0/examples/dfu/bootloader_secure" and the buttonless...
Hi together,
I'm using nrf52832, SDK 12.1.0 and S132 3.1.0.
I integrated the peer manager to my application code and have the following questions concerning the bonding...
Hi,
I noticed a possible issue in BSP_MS_TO_TICK macro computation.
In bsp.c, the macro is defined as:
#define BSP_MS_TO_TICK(MS) (m_app_ticks_per_100ms * (MS / 100...
