Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello, i am seeing a strange behaviour of pstorage module and i don't understand what is happening. I have read links below:
pstorage-problem-on-power-off
saving-data...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
I am trying to implement the ANT+ Environment Profile using the nRF51 DK and I was wondering if anyone had done this and could point me in the right direction to start. I...
how to synchronize multiple NRF52 them?
Should I use a router? What route do you recommend for development?
Otherwise many people tell me that the Bluetooth has a very...
Hi all,
I create 4 timer in APP, and there seem only one timer (work in single shot mode) can not trigger by right ticks.
I add some log and find that:
First I...
Noticed in ant_parameters.h
#define MAX_ANT_CHANNELS ((uint8_t)15)
First question: is this correct for nRF51?
Second question: is nRF51 going to support 15 channels...
Sorry for the newbie question -- I am new to programming microcontrollers.
I would like to know if it is possible to program the nRF24LU1+ to behave like a USB host? I...
Hi!
Is this correct scenario to minimize battery usage for radio tag transmitting 8 byte packets at 3 Hz?:
setup:
turn LFCLKSRC on with CLOCK_LFCLKSRC_SRC_Xtal...
Hi all, i am trying to start using the smart beacon kit nRF51822, but searching around i am a bit confused on how to flash the most recent softdevice with sdk on it; i followed...
I'd like to do the same thing :
how to use dm_device_delete
nRF51822 S110 v8.0.0
nRF51 SDK v10.0.0
DEVICE_MANAGER_MAX_BONDS=2
I test Nexus5, Nexus7, iPad...
I want to read and write RAM (target=nRF51822) from a custom C application while the CPU is running.
Now, I can do this using the nrfjprog.dll and I get the expected values...
Hey guys,
I'm working with a nordic nrf5182 and s130. What I need is to put the system in sleep mode after a reset. The main problem is with function sd_power_system_off...
hi,I have to question about ADC,please help me ,thank you very much!
I joined on the ADC input pin an adjustable resistance, to change the voltage value.Why change the...
