Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
Finally, after some struggle, I achieved to port the bootloader to s120 V2.1.0 and work just great on a dev. board with nRF51422. But now I have another problem...
Hi, i hope i'm not duplicating any questions, but i couldn't find a similar one.
I worked with other ARM micros in both mbed and Keil before, but i'm new to Nordic Semiconductor...
Hello,
I getting started with nrf51 DK.
I followed with many blogs.
I checked errors, and fixed. And I builded the example 'blinky'
But my nrf51 is not blinked.....
Hi all,
I am doing the PTS and meet some issues here:
Using the SDK 8.0 KB demo with SD8.0;
Do the profile test with PTS dongle and tool, and return errors on...
Hello everybody,
I'm using NRF Beacon (51822) board, sdk 6.1.0.0 and s110, problem is when I enable whitelist and add the Bluetooth address of my phone( 74:51:BA:F7:60:9F...
In my bootloader I'm using sd_flash_page_erase() directly without pstorage.
The flash erase performance is exceedingly slow. It is taking 13.187 seconds to erase 132 pages...
Hello!
We are thinking about creating some devices for Apple HomeKit.
But devices for HomeKit have to go through one thing: Apple certification. And one part of the certification...
Hi
Maybe silly question:
I was wondering: if I cast a pointer to a uint32_t to an array "buff" of uint8_t, what is held in buff[0], MSByte or LSByte?
Or in other words...
Having just upgraded to the Soft Device 6.0.0 and SDK 5.1.0, I can no longer flash my nRF51822 from Keil. I get this in the Keil console:
Load "C:\\Users\\Eliot\\dev\\nrf51_sdk...
Hi,
I'm designing a four layer flex PCB with the nRF51822-CFAC and recommended ST BAL-NRF02D3 balun and PCB trace antenna (not chip). I have a couple of questions.
...
Greetings,
Using the "central multilink" example project, how do I stop scanning if no advertisers are found? I see a case BLE_GAP_EVT_TIMEOUT in function on_ble_evt() but...
Hello
I found similar questions but no answer?
In the manual is written that I can control the parity bit in manual mode with the TXPARITY register but I can not find how...
what may be the reason for app_assert _callback error in s130,ble_central_and_peripheral that occurs from the following 2 lines
sd_softdevice_enable((uint32_t)NRF_CLOCK_LFCLKSRC_XTAL_75_PPM...
I have Rezence SDK working well with Keil uversion with wired and wireless debug without any issues on either nRF51 and nrf51822 DKs. When I port the project to Eclipse with...
Using the bootloader example code in SDK 8.1.0 for gcc, roughly how long does it take from power on to the call to bootloader_app_start()?
My device is motion activated...
