Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
Hi,
I encountered some problems when using UARTE.
In terms of hardware, I have connected the 52840DK LOOPBACK_PIN_1A and LOOPBACK_PIN_1B.
Software code is the original...
Hello,
I see that kiss_fft is used in the libLC3 library. I would like to use it for another part of my product in addition to the pre-compiled LC3 lib, but don't want to...
I'm pretty new to embedded development/electronics and I'm trying to interface with a I2C pressure sensor, but I can't seem to communicate with it. I'm using nrf52840dk board...
Hello,
Up until today I had been developing fine with visual studio code, installed via Toolchain Manager. Then, I clicked "Pristine Build" for the first time in a few days...
I installed the VSCode extension for nrf connect.
I want to do the build on this page:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/thread/tools.html...
Hello Team,
example: SPI master_slave advanced non -blocking
i just open nRF connect sdk example in vs code and build it
I am getting below error while build
Please...
Hello,
I am trying to play with zephyr networking samples on my nRF5340 + nRF7002 EK devkit board.
I am using NCS 2.7.0 release SDK. i was able to build and run some Wi...
I'm not sure if zephyr questions can be also asked here. Problem I am struggling with is approtect mechanism to prevent flash readout. I am trying to use Zephyr config files...
Hi,
I am currently developing a custom Zigbee end device with support for FOTA updates. My FOTA seems to work (all data gets transferred correctly) but the update won't...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello,
I am uploading my code with a basic URI to be advertised by the chip.
I am able to build and upload the code for the nrf52832 in my nrf52 DK, the program works...
