Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...
Hi, I'm new to Nordic Semiconductor chips.
I have experience programming STM32 and Atmel microprocessors. I would need to program/debug the NORDIC nRF52832 chip, without...
Hello there, I am working on enabling/ disabling DFU in nrf52840dk using ncs 2.4.2. previously i was doing it using ncs 1.8.0 as follows: libraries used:
#include <mgmt...
Hi,
I use the above function to create a new dataset. When I use SDK 2.3.0, this works perfectly. But when I use SDK 2.6.0 I get the following.
When I tried
arm-zephyr...
Hi all!
So I'm just starting out with the Thingy 91 and I was following the Nordic Thingy 91: Getting Starting Guide and I was in the process of using MCUBoot to update...
I am using nrf7002-dk as client and running the server python code in my PC and I am using ngrok command line tool get alternate http link.
I am using wifi-fund lesson4...
Since https://github.com/nrfconnect/sdk-nrf has disabled issues, this is an assorted list of problems/limitations with the lte_net_if library ( https://github.com/nrfconnect...
Hi All,
I want to do dfu over uart with secure bootloader, am using nrf52840-DK, nRF5_SDK_17.1.0_ddde560 SDK and segger embedded studio V8.10.
compiled and flashed secure_bootloader_uart_mbr_pca10056_debug...
I use DWM3001C chip,it has a nrf52833 mcu inside.when i call ble_init() in main.c.it report error:
peer_manager_pds: Could not initialize flash storage. fds_init() returned...
Hi Team, I'm trying to port the acconeer project that worked on the old one NCS v2.2.0 to new NCS v2.5.2 and ran into a problem with the difference
c:/ncs/toolchains/c57af46cb7...
I am trying to use libmodem in a bare-metal app on a 9151dk, but nrf_modem_init() is hanging (not returning). What conditions can cause this? The issue looks a little like...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
