I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
Hello,
I want to use standalone logging for each file (/module)(/driver) of my program, therefore register different logging modules with different log levels each. Registering...
Hi,
I am attempting to configure a nRF52840 (packaged as Seeeduino XIAO Sense) for the popular printer software Klipper.
i have the following processor options and am...
Hello I'm trying to use GPIO pins as UART on the nRF 52 DK rather than the default UART pins. How do I change the pin configuration? I'm using nRF SDK version 17.1. 0
I now have two dk's, one as a master and the other as a slave. The slave sends data to the master, and the master forwards the data to the PC. That is, the piece of dk that...
We are seeing an issue with Android 13 on Samsung phones connecting to our device over BLE. After CONNECT_IND the phone will attempt to send a LL_FEATURE_REQ. It takes about...
Above is the code that im using.
Module - BT832x
Debugger - Segger J-link
IDE - Segger IDE
SDK - nRF5_SDK_17.0.2_d674dde (Downloaded from nordic website)
Program...
Hello Nordic Team,
I am facing an issue in my project that uses BLE and FreeRTOS. If I call nrf_sdh_enable_request () in main() before starting the task scheduler vTaskStartScheduler...
Hi,
I use 2 nrf52840 custom board, one is use a peripheral sensor with a lot of services and the other is used as a central with bt_shell_command.
Now i need to be able...
Hello Nordic support,
I am working on an application that works either with BLE or Zigbee and the protocol to be used is determined at application startup. Initially, my...
Hi Nordic Team,
I want to build NET core project for NRF5340 DK audio board, so I select build board config with nrf5340_audio_dk_nrf5340_cpunet, then build configuration...
Hi,
I have some questions about the quaterwave monopole antenna.
In the papers of Nordic I did read:
If the ground plane size is considerably smaller than the ideal...
Hi,
I have problems with the RTT up buffer overflowing with the standard configuration.
CONFIG_LOG_BACKEND_RTT_BUFFER_SIZE does exactly what I need, but it requires CONFIG_LOG_BACKEND_RTT_BUFFER...
Hello Nordic/Zephyr, MS VSCode has a page on reference variable: https://code.visualstudio.com/docs/editor/variables-reference I known Nordic/Zephyr has also such variable...
