I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have noticed that the function sd_rpc_open(...) of pc-ble-driver takes more than 1.5 seconds.
I have tried an example heart_rate_monitor which is supplied with pc-ble...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0.
I want to dynamically control CLOCK source.
I tried to release( STOP ) HFCLK( XTAL ) source using nrf_drv_clock_hfclk_release...
Hi there
When the EVENTS_DEVMATCH is raised, this signals that the device address received in the radio data packet matches one of all enabled addresses in the BASE0/BASE1...
Hello,
we faced sometimes the issue that the reset reason Register RESETREAS is Zero at Startup. What does it tell me? So what happend in the Firmware that there is a reset...
I haven't been able to find any documentation or forum posts along the lines of the problem I'm having, so...
I'm trying to use an nRF52-DK with nRF Connect Desktop to connect...
Hi,
I'm using nRF52840 with NCS 1.8 on the existing ongoing development project.
Recently I implemented shell commands, to be used during testing procedure either via...
Hello
I have seen that using SDK 1.17 there is a possibility to set one channel that will be scan 37/38/39. I looked on SDK 2.2 documentation and I didn't seen this option...
Hi
We encountered speed issues with the download client library and CONFIG_DFU_TARGET. The problem can be reproduced using the download example. Without any changes I usually...
Hello,
Im working right now on a product which saves the update file (init + app packet) on its Flash in a specified memory section.
After "uploading" the file in the...
I have integrated MCUMGR to perform FOTA and it does successfully perform the updates where both slot0 and slot1 locations are from internal flash. As the code size is getting...
Hello !
I bought a new nRF51DK board and need to read its RAM data. I used nRF connect to erase it. The data read by nRF connect shows 262144 bytes and I don't know the...
Reproduce issue:
Windows 10 21H2
Set global git option gpg.format to ssh
git config --global gpg.format ssh
Install nRF Connect SDK v2.0.2 with Toolchain...
We are using the external flash w25q32jv via SPIM connection. the configuration as below.
arduino_spi : & spi3 {
status = "okay" ;
compatible = "nordic,nrf-spim" ;...
Hello-
I'm seeing the nRF52840 stay awake when I don't want it to. I'm calling sd_app_evt_wait() every turn through the main loop with SEVONPEND disabled, but it's waking...
