Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I was just wondering if the nrf52840 Dongle is in some ways inferior to the other development boards in terms of its capabilities?
As I was going through the examples...
Hi,
I am using a nrf528409dk for my application development using nCS. I have various features from which I need to understand how to add some high priority features into...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
We want to start with ble_app_uart example for our product but it the firmware halts at CRITICAL_REGION_EXIT() in nrf_sdh_enable_request.
We are using the example from 17...
Hiii, is there any libraries or example to read nfc tag through clrc663 nfc reader, could any one direct me to the any solution
thanx in advance
suprith
I am having problems setting up UART communication between nrf9160 and nrf52840 on Thingy91. My set up consist of a Thingy52 and a Thingy91. I am using ncs version 2.0.1....
Hi,
I've been working on Open Thread recently. I found that after I send provisioning request, even though there are 3 servers "enabled provisioning", the callback function...
Hi,
I am trying to setup a raspberry pi 0-W for flashing nrf devices. But nrfjprog doesn't seems to work.
I am using Raspberry Pi OS (32-bit).
I have fetched Segger...
