Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi
Currently, I am developing an application to send larger data over BLE through custom service. I have referred to multiple tickets on devzone was able to send the data...
Dear All, I wonder if there is a way to redirect the logging operations to any kind of persistent memory type, so that a device can be debugged even when it is not possible...
A few days ago, I tried project "hci_uart" of zephyr on nrf52832 and succeed. Now I want to know if there is any method running "hci_uart" with Qemu? May be it is hard?
Hi Friends,
I want to test nfc_uart_tag sample app using nRF52840 and NFC_tools mobile app.
I want to read the data sent on uart with NFC_tools.
and write the data with...
I was trying to debug an issue with a release build on our firmware. I modified app_error_fault_handler inverting the NDEBUG logic so that the error code, line number and...
Dear Nordic Engineers
I encounter a issue about gpiote channel() function of NCS 2.0.0.
I use gpio_nrfx_pin_configurationl() to judg gpiote channel is be occupied.
It...
Hi,
Iam using UART Driver Sample — Zephyr Project Documentation (nordicsemi.com)
Where to change the UART TX Rx Pin in the UART Driver Sample(echo bot) program in nRF...
Hello,
I want to define SPI outputs as highdrive outputs in a overlay file.
I know how to do this in the code:
But I want to do this in this overlay file:
How...
Hello,
We are using nRF52833 Soc and s140 soft device for our project. Application is scanning our proprietary Tags. We have Bootloader as well to support DFU.
Due...
I'm currently doing some research for a project and intend to use nRF5340 Audio DKs and the Audio Application. I need access to the LC3 repository to build the application...
Hi,
My Homekit project is based on v1.9.1 NCS.
with CONFIGs: CONFIG_DATE_TIME=y CONFIG_DATE_TIME_MODEM=n CONFIG_DATE_TIME_NTP=n
I use our iOS app to sync the current...
Hi guys. I am using nRF52840. Currently, I want to read out an image from a camera. The camera PCLK is toggled at 500Khz, and what I want to do is to trigger an interrupt...
We just recently started testing with slave latency above 0 to save power. Our connection interval is 60. If we have a slave latency above 3, then the connection terminates...
Hello,
I want to calculate RSSI using TX power(Measured power at 1m) and instant RSSI getting in NRF CONNECT APP and Environmental factor.
I have used this
Distance...
