I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi there,
As mentioned in an earlier ticket I'm developing a successor to one of our products based on the nRF9160. Since it doesn't have USB we've added the nRF52820 as...
Hi all,
Inherited a nRF Connect 1.5 project developed under Linux and I'm trying to get everything set up for continued development under Windows.
I can build the code...
I modified the simple_gw example code, when the end device(application/light_sample/dimmable_light/bulb, I did not modify this example code) joined the ZigBee gateway network...
I like to implement transfer layer on UART communication, since data error is possible on UART.
I read this " UART HCI protocol" document on Nordic SDK.
https://infocenter...
Hi all,
I think this question is generic and covers all Nordic chipsets. Anyhow, I'm planning to use a nRF52810 but I don't have a board to confirm this yet.
Question...
HI i am working with the nrf 52833 dk board using nrf connect and trying to implement SPI ,
#define SPI3_NODE DT_NODELABEL (SPI_3)
static const struct spi_dt_spec* dev_spi...
For some reason when we build a MESH enabled app we are getting a resulting hex file that includes complete file paths names. This is not occurring in our builds that do not...
For my application, most of the time, the device is asleep with the exception of sensor reading and logging every 5 minutes and occasional (and infrequent) beaconing so the...
Hello to all,
I countered the follwoing issue at starting debug phase of my project:
In details:
I think that I have to update the GDB to version >=9.
Could...
Hi,
In my application, I want to read some sensor data through SPI Communication in nrf52840, can you please provide some code or please tell me how to implement the program...
Hi,
I am using nrf connect sdk V2.0.0 and nrf5340 DK.
Using fat_fs and uart examples, I managed to get the SD card and UART work individually. For SD card, I am using...
I have build many applications using the NRF5 SDK. I have a custom service that works fine on all my applications written using NRF5.
I am now trying to port these applications...
Hi,
I want to do full modem update. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/http_update/full_modem_update/README.html My device...
Hello,
I am working with nRF5 SDK v17.1.0 and using nRF52832DK board. While working with SAADC module I found that nrfx_saadc_sample_convert() API is taking almost 35us...
Hello, when I try to debug ncs1.9.1 using vscode in Windows, it shows that "ERROR: GDB major version should be >= 9, yours is 8; GDB could not start as expected. Bad installation...
