Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I have a few queries:
I need to confirm that does Thingy53 board support TensorFlow lite. So, for my ongoing project, I am using TensorFlow to develop my code...
Hello,
I am facing an issue at running otbr docker conainer on my RPi4 with nRF52840 Dongle as an RCP device . I am getting this error on the logs: Aug 24 16:05:07 0e6bb978e199...
Hi!
I have tried to get the secure_bootloader working on the nRF52820, but I think the linker settings are not correct yet. Maybe someone here has already written a bootloader...
Hello,
I am trying to build OpenThread Radio Co-Processor (RCP) firmware for nRF52840 Dongle with the new nRF Connect SDK v2.0.2. My VM is running Ubuntu 20.04.3 LTS with...
Hello!
I have an application that makes use of the function sd_ble_gap_conn_evt_trigger_start() , present in v7.3.0 of the S113 , S132 , and S140 SoftDevices. Here's the...
Hi,
1. I can use Programmer in nRF Connect for Desktop to flash the hex file ( nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images\ble\nrf52832sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Greetings,
I want to write the nRF Connect SDK v2.0.0 sample "nrf9160/https_client" to the nRF9160-DK, but when I use "Flash" in Visual Studio Code, the following error...
Hi,
I'm designing a drone based on these three Nordic IC:
nPM1100
nRF5340
nRF21540
Let's Start with nPM1100:
Based on this Reference circuitry
I based my...
On SDK 2.0.2, I was able to load peripheral_uart with CONFIG_BOOTLOADER_MCUBOOT=y and successfully update both the app core and net core using the thingy53. However when moving...
Hey,
I bought a device which uses the N52832 SoC, Im gonna attach a photo of the device. Is it possible to get the code from the device, modify it and then upload it to...
Do you know of any way of reading the installed modem version of an un-locked nrf9160 through the j-link programmer. I would like to conditionally program the modem firmware...
