Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
We are developing a product using the N52810 chip. We have J-link, and by downloading and connecting the Rf test tool,
the result is that there is no firmware. Can you support...
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
We are looking to use freeRTOS instead of zephyr on this board.
Finally with freeRTOS...
Dear Nordic support team
I tried to change the sample of ble_app_uart (nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040e) to support connecting 4 mobile...
I am working on an e-paper display with Bluefruit nRF52832 . I need to transfer a large image bitmap over Bluetooth Low Energy (BLE).
As BLE can send 255 bits at once, how...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
Hey there!
The DFU over serial was successfully implemented. Unfortunately, I was only able to update the first node of my mesh, not all of them.
The first node in the...
Hello!
Recently I want to write a hci vs command in zephyr using nrf connect sdk, when I track ncs_v1.9.1\zephyr\samples\bluetooth\hci_pwr_ctrl samples code and find it...
Hi, for nRF5340 the "Build code" is a string of 3 chars
H - Hardware version code P - Production configuration code F - Firmware version code
https://infocenter.nordicsemi...
Hi
I am testing a thermometer peripheral using the nRF52840DK. It is advertising using BT LE Coded (BT_LE_ADV_OPT_CODED) with an advertising frequency of 3 seconds.
...
Dear Nordic Support Team,
I would like my nRF9160 DK to connect to multiple servers using TLS. Among others, I have read the following documentation: nRF9160: Simple MQTT...
APN setting of nRF9160 cannot be done well.
I am using soracom's SIM, and the contents are as follows.
(When I checked, it was a SIM that supports LTE-M.)
Name: Any (Example...
I'm relatively new to both nRF and Zephyr platforms and I'm wondering how to disable UART on the UART pins (such as p0.19-p0.22 on the nRF5340 that I'm using) so that they...
