Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
Trying out Nrf5 sdk v17.1 with SES 6.32 and opened up an ANT+ example `ant\ant_debug\d52\s212\ses`
Tried to build, 50% compiled successfully, but i get repeated errors on...
We use nrf52833, and the SDK is 17.1.0. We have the following questions about gzll: 1. How to count packets_num and timeouts_num in Packets Statistics? timeouts_num Where...
Hello,
I am trying to send a large file through BLE from an nRF52811 to a Raspberry Pi 4. File size is about 77 kilobytes.
Here is BLE setup on the nRF side:
Custom...
Using the DM, in the discovery_complete callback, after finding two CCC handles from 2 custom UUID's, I can subscribe to only one of the two, the other fails with EALREADY...
Hi,
I am not sure where to go next, so looking for some debug help.
Setup : I am using the 9160DK - the 52840 is being used as an ANT+ receiver, where it forwards on UARTE...
I am working with the AWS IoT sample on the nRF9160 development kit using Nrf connect 1.8.0. I am testing the disconnection behavior by removing the sim card after connection...
Hello to all :-)
i am not sure if this is an Hardware-topic, but i want to know the possibilities how to can
use and configure the nRF5340 (where can i find a detailled...
Following some previous posts on how to get the Bootloader version from the application, mainly this post: devzone.nordicsemi.com/.../221367
I noticed that initially the...
