Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am using Thingy 91 in Australia, and I have linked Asset Tracker v2 with overlay-lwm2m.conf to communicate with my own LwM2M server, which is running an instance of...
I'm working towards getting an app derived from MQTT Simple to talk to AWS where I both need to validate the hostname via TLS, and also use public/private certificates to...
Several have asked about this basic situation but I have found no definitive answer.
I erased a dongle with a Segger J-link, and compiled the zephyr samples using CONFIG_BOARD_HAS_NRF5_BOOTLOADER...
My set up is nRF52832 with a board very much like the PCA10040. The SDK is version 16.0.0. I am using Segger Embedded Studio version 5.60 and I am using the GCC compiler suite...
My goal is to have my boot loader write a constant value to RAM and have my applicaton read that same location and retrieve that value.
I am using the stock boot loader...
Hello,
I'm creating a BLE project with a couple of custom services. One of my simple characteristics in a service is a string. When is_value_user = false everything works...
Hey! I am starting my studies in the BLE protocol and I would like to send the ZE03 sensor data through the Nordic UART Service (NUS).
The sensor has 9 bits: 8 data bits...
Hi, I have made a 9160 board, below is the schematic diagram ：
I donwload this example in it, " ncs\v1.9.1\nrf\applications\serial_lte_modem", and send AT command to test...
My Windows app sends command though Nordic UART service to nrf52832 device. Does nrf52832 need to send ACK to let Windows App knows it has received command?
Hi,
I'm using a nrf52832 board. In this case, updating the bootloader is necessary. So, does mcuboot have a way to update itself? , and if not, what alternative method of...
Hello,
I'm trying to move from nRF5 SDK with nRF52840 to NCS with nRF5340 and experiencing a lot of problems replacing the nrf driver functions with nrfx.
Thanks to...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Segger Embedded Studio 4.16
Aim: Controlling...
Hello everybody
I'm trying to initialise an advertising module for my project.
When using the macro for creating an advertising instante I get the following:
After...
hi,
In my application, which was based on nRF_SDK_Thread, to check my node's connection with the Border router, or to know whether the border router is present or not...
