I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
Hi.
In a prototype built for a small group of test users (20-25), we want to implement a simple tactile reset button for use in case of an anomaly (as the prototype software...
Hello,
I am using nRF9160 dev kit in Chicago (USA) and in Aldingen (Germany) where I am using same firmware for both DK to get GPS Fixes for location. But surprisingly in...
good try,
i tried adding buttonless dfu service to ble hid_mouse/keyboard sample in nRF52 SDK 17.1 with PCA10040 dev board but it does not show up in the list of devices...
If the privacy feature is disabled, calling bt_conn_le_create will change the state to BT_CONN_CONNECTING_SCAN (since bt_dev.le.rl_size == 0) and then call bt_le_scan_update...
Hello,
I have been working with Adafruit Feather nRF52 Bluefruit LE for my project, I have two of these modules.
Recently, while I uploaded code into it and push the reset...
Dear Forum,
I am using the provided BLE-NUS UART examples (central/peripheral) to create a COM link via bluetooth.
As I failed to generate a setup which directly operates...
I am using SDK_17.1.0_ddde560 and IAR compiler for the project. We want to create a makefile based compilation for IAR.
Are there any examples wherein makefile is used with...
Hi,
I am looking at this page for nRF25832 https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.1.0/lib_bootloader.html
and I notice that the Application area (incl...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But nRF Connect can connect nRF52832 without passkey...
