Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I am developing FW on NRF52840_DK using nRF SDK Connect v1.9.1 for a BLE Peripheral as a Reader.
The Max Application Data Size (Tx, Rx) to be supported for Mobile...
We are using nRF9160 DK for tests (as well as nRF9160 on our custom board) sdk 1.9.1. Our product requires getting coordinates and for this we use AGPS, GPS and Cellular Position...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
How to resolve this Fatal error...
Hello,
I am developing FW for a BLE Peripheral on NRF52840_DK using nRF Connect SDK v1.9.1 on VScode.
So far, Peripheral and Client are able to connect and exhange data...
Hi All.
Can I know the minimum Flash & RAM memory I need in my module, to run an specific example source file, from which I have the following info:
Thanks.
Juan
Hi I want to advertising with NRF52840 DK, I do tutorial explanation and for PCA10056\S140 after load main.c it compile without any error and warning but I cant find any device...
Hello,
We are developing an application based on nrf52840.
We have succefully made transactions with advertisment packets, including also Gatt service with read/write...
Crawling up the learning curve here, doing my best to solve my own problems, but I'm down to just permuting things on this one and I'm not making much progress and all the...
I want to run BLE peripheral UART application on nRF51822. I have downloaded nrf5 SDK and S130 softdevice. I am using Keil5 and STlinkV2 for programming the device. The UART...
Hello,
I'm currently working with an nRF5340DK , trying to implement FOTA update by sending the firmware from another nRF5340DK . Is there an already developed feature/sample...
Hi,
I'm using the nRF5340 DK. I am trying to get iso_broadcast sample application working but it fails when creating a BIG (-5 error) (there is a prior support ticket for...
Our startup previously used nrfx 2.4.0 but worked just fine. Upgrading to nrfx 2.8.0 results in a Hard Fault at the location seen in the screenshot. Which is the file located...
Hi,
I am posting this here because I am not sure exactly which repository to file the bug on (zephyr? west? something else?)
nrfjprog supports programming over IP with...
I'm still new to Zephyr, so this could be an easy question that I'm googling poorly - if so, sorry in advance. I just wanted to add an extra LED, led4 , to the existing nrf9160dk...
