Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I am currently working on NUS sample code with one nRF5340 as central board and ISP2053 module as the Peripheral to send data with 264kbps. The peripheral is flashed...
Hi. I am currently working on a project using the nPM1300 as a pmic. For this i have a battery and an nrf5340 connected to it. Using zephyr i have even the following options...
Hi Nordic team,
I’m building a device that uses nRF9151 for cellular and an nRF7002 companion for Wi-Fi. My requirement is simple:
If a known Wi-Fi network is available...
Hi there,
I found the FW swap time in Mcuboot is too long. debugging into the code, the function, boot_move_sector_up, take ~20s, my FW is ~600k. It means the flash erase...
Hello,
Our current design does not use an external crystal for the LFCLK. As a consequence, I configured the LFCLK to use the RC oscillator. We also have power consumption...
We are using the nPM2100 with a CR2050 and CR2077 battery. There is a battery model for the CR2032 coin cell in the nrfxlib. Are there also battery models available for CR2050...
Hello,
I'm trying to add MCUBoot with sysbuild to my application (nRF Connect SDK 2.9.1). I have added sysbuild.conf (in the project's root directory), with single line...
Trying to make Thingy91's asset_tracker_v2 light sensor (BH1749) data to show up in a card on Dashboard in nrfcloud. By default asset_tracker_v2 code supporting light sensor...
Good afternoon!
I didn't find a post with a solution to my problem. If I overlooked something, please feel free to just redirect me :)
Goal: In our project we want the...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hi Nordic community,
How do I change the start address of an NRF54L15 application in NCS Zephyr?
I need an address other than the default 0.
I have tried adding
...
Hi,
I know that the nRF54LM20A was just announced but since it has USB support I am considering it as an option to replace the nRF52840 in the future. Looking at the preliminary...
I'm currently debugging a problem where my Zigbee End Device (ZED) occasionally never sends an association request to my Zigbee Coordinator (ZC). My ZED is a nRF5340DK using...
Hello, I'm currently building a zigbee end device using the Zigbee Template example on the nRF5340DK but I am having issues regarding rejoins. My Zigbee Coordinator(ZC) is...
Hello,
I am working with the nRF5340 and would like to measure BLE throughput. I know that typically a throughput test requires two devices (central and peripheral), but...
