Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
In sdk 16 release notes i have read 52810 chips are supported for gazell secure libraries. But when i make the project port changes as described in "developing for 52810"...
Any recommendation for a filesystem for nand flash?
My application uses zephyr on nrf85240 with a 128MB nand flash.
It samples sensors and streams their data to the flash...
dear nordic team,
I was working on nrf52840 with nrf5sdk v 17.0.1 and sd v7.3 .Im using mergehex tool to combine bootloader+softdevice + App to download it to flash(using...
Hi Everyone.
IDE : Vs Code
SDK : nrfConnect SDK
I have tried to connect peripheral device based on address. User gives input , address of ble device and based on that...
Hi, I am trying to provision device using nRF mesh application. It discovers device and when i try to connect, it gives error device disconnected.
I tried this thing on...
Hi everyone, in special, Nordic; I'm facing a problem with the last two versions of the NRF CONNECT for Desktop (3.9.2/3) & the BitDefender Antivirus... I can download & install...
Hi everyone
I'm trying to generate the .hex file for examples like Tx and Rx or for my project but I'm not able to do that, please can anyone suggest me how can i do that...
I had been able to program my custom nRF52840 just fine until I wanted to change partitions. I erased everything and now am unable to communicate with the board at all. I...
https://github.com/NordicSemiconductor/pc-ble-driver-py/issues/210#issue-1089773469
I'm trying to build the project from sources. -using windows 10, python 3.8 -installed...
Port the radio_test sample to the Coprocessor sample to test the radio_test function error
How do I merge the two examples
I was hoping you could help me out
many...
Dear Sir.
We are using software based on mqtt simple project .
We added a 1 hz timer, Every 1 hz we toggle a led on and off.
Sometime the led is stuck on " on "...
Hi,
I'm trying to broadcast my BLE on my custom-made NRF51822 custom board.
My code was intended to run on Nrf51422, and it runs correctly on my PCA10028 DK with NRF514...
Hi,
we are working on nRF52832. my hardware is getting reset after a time. i don't know reset reason. my question is how to get cause of reset.
thank you
Hello,
I'm using the library LVGL on the board nRF9160 DK with an LCD screen.
In the lastest version of nRF Connect SDK (v.1.8.0), the version v7 is used for the library...
Hi,
The RAM Loading section for MCUboot states the following:
In case these drawbacks were acceptable, is it possible to run the image from external storage, without...
