Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
nRF Connect SDK v1.7.1 sample \ncs\v1.7.1\nrf\samples\bluetooth\mesh\light_ctrl\
Long transition times fail due to a 16bit value which needs to be 32bit (I believe, can...
Question regarding nrf5340 ADC input tolerance
If I power the nrf5340 from the VDDH pin at 5V, will the ADC input pins be able to read up to 5V then or just 3.3V?
Thanks...
We have a product that uses the nrf52. Due to availability issues I need to port that project to the nrf51822. Since the nrf51 supports up to sdk 12.3.0 what is the best way...
Hello All,
Thank you in advance for your time and interest in this issue and willingness to provide suggestions.
We have a product that uses the nRF52832 processor in...
Hello,
I'm trying to connect a sensor to the nRF9160 board using the example Asset Tracker v2.
My sensor (SHT30) is connect in I2C to the pins 31 (SCL) and 30 (SDA). In...
Hello,
Does nrf9160 support C++? If it does, which version? I saw a similar question over 2 years ago in which C++ was not recommended ( https://devzone.nordicsemi.com/f...
SDK: v17
Softdevice: S112
I am currently checking the throughput using nrf52810 or nrf52805.
In device A, data is input as Uart and checked as device B input data...
Hello everyone! I want to evaluate the exact power consumption from the camera (Arducam Mini 2MP OV2640) using the nRF52840-DK as well as its SDK with the nrf52-ble-image...
Hi,
I am trying to implement USB DFU on a NRF52833 with nRF5 SDK for Thread and Zigbee v4.1.0 and nRF5 SDK v16.0.0.
In a first step I want to perform this on the devkit...
Hello,
I have several issues with the new nRF Connect for VS Code SDK, I put them into one ticket, although, some of the issues could be related directly to nRF Connect...
Hi
1: According to this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/28335/nrf52840-usb-pins-impedance you recommend to not
have any serial resistors on the D...
Hello!
I have installed Android nRF Mesh application version 3.0.3.
Also I bought Yeelight YLDP10YL lamp which is qualified mesh product ( https://www.bluetooth.com/learn...
Hello,
I am getting a bit lost in the pool of different versions and libraries. For simplicity, I just want to achieve a single goal to start which is send a bluetooth packet...
