Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi I am trying to do the led blinking in nrf52840 but the led is not even turning on i have given the code below can any body help me out.
nrf_gpio_cfg_output(14); nrf_gpio_cfg_output...
Hello,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
I recently purchased a Thingy 52 with the goal of processing the the raw magnetometer, accelerometer and gyroscope data using a sensor fusion algorithm to determine orientation...
Hello, We're about to start a new project with the nrf5340 as our SoC. When reading the docs for the nrf5340 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I have problem with wakeup of Low Power Node from System ON sleep mode. In debug session code works as expected, however outside the session something gets wrong.
The node...
Hi,
I'm trying to create an application based on the SMP Server app (NCS v1.7.0). I'm able to perform a FOTA using nRF Connect for Mobile and the app._update.bin without...
Hi,
I use the ble-app-uart-c-multilink example with a nRF52840 DK and 5 custom nRF52840 peripheral devices.
For a test, I want to connect to only one of those peripherals...
I am a newbie in nrF52832. I have been carrying some experiments using the Nrf51 and so far they are going so well. However, I came across some few E104-BT5052 samples originating...
In ncs1.7.1, I’m struggling with a problem about hard fault on nRF9160, but I have no idea to slove the problem.
nRF52840 transmits data to nRF9160 via UART0, the baudrate...
Hi,
I got the example http://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role and the demo is OK.
I also use nRF Connect APP to connect the ble_aggregator,...
Hi,
Hope you are doing good.
I run the SAADC signal to from the sdk and observed that when the adc input is connected to ground, the adc reads few random negative value...
Using nRF9160, ncs 1.6 on a custom board and segger-SES for debugging, we have intermittent stops (debugger breaks) on an assembler line with 'cpsie' opcode:
File: cpu_idle...
Hello Nordic support,
I am using nRF5 SDK for a Zigbee coordinator application. In zboss_api.h, I see that there are functions for setting short pan id (zb_set_pan_id()...
Hi, I'm starting a new custom development, that will use NRF52805 SOC. The project will be one Alexa Gadget device. I have seen several documentations, but I have some question...
