Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm having some difficulty understanding what the nRF53 datasheet is trying to tell us about the internal load capacitors and related items. We are using both the LFXO and...
Hi!
There are many questions regarding the high voltage mode of the nRF5340 already in this Q&A, but I don't see the answer to the question, how it is enabled programmatically...
Hello, is it possible to set gpio direction (input/output) from devicetree?
I haven't found any gpio flags to do this in the gpio.h located in dt-bindings folder.
Hi all. The current devices we are developing are made with NRF52832 based on the NRF SDK v16. We also plan to use the Wirepas stack. Initially, we want to implement support...
hi
i have developed my device,and it was work in customs,but there is some device cant work after work some times.we recall the device and discover the firmware was loseed...
Hello,
I have a question regarding GPIO setting during sleep mode.
nRF52832 is sleep and wake-up by GPIO state(Red in below picture).
When Red is high, nRF52832 go...
We are trying to implement errata 254, but I've run into a couple of questions. What's the correct test to see if the device needs the workaround for the errata? NRF_FICR...
Hi, I am using pc-ble-driver v4.1.4 combined with connectivity firmware compiled with s132 v6.1.1. My application is running on custom hardware with a cp210x serial to usb...
Hi, i made some research on the VMA323 sensor, how to get it to work with my Nrf5340dk but i didn't find any documentation is there any available documentation about this...
Hello sir,
I am using nrf52832 Dev board and write the value '1' through nrf connect app by enabling the notification enabled with case length one i.e (p_evt_write->len...
//this ticket is a diversion of this ticket @Increment Counter on Button Clicked https://devzone.nordicsemi.com/f/nordic-q-a/82239/increment-counter-on-button-clicked Hello...
Hi,
I have used an NRF9160 in Belgium with the iBasis sim card, connecting via LTE-M and NB-IoT with operators Orange and Proximus. HTTP requests work fine.
However, when...
I'm running nRF Connect Extension Pack on macOS within VS Code
Whenever a Build or Pristine Build has finished the terminal shows this message:
Terminal will be reused...
Dear NCS experts,
Considering a Bluetooth Mesh firmware application based on nRF Connect SDK 1.7.1 that is running on a nRF52832: How do you enable/disable the gatt proxy...
