Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
The application of a device is developed based on ncs1.3.0, now the SDK version is upgraded, the firmware function is developed based on ncs1.5.1, and a problem is found,...
Hello,
I'm in an aging manufacturing space and would like to utilize your sensors, but im concerned the pillars and walls will prevent data from being sent. I read the...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
Hi,
I'm using spim on nRF52810.After I init the spi driver and using APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, &Command, 1, m_rx_buf, 1)) , RTT Viewer showing FATAL ERROR...
Hi,
Is there a way to control the 1Mhz BLE symbol clock?
We want to use nrf52840 as a GFSK transceiver and we need to control the symbol clock (up to +- Khz resolution...
Hi,
I'm running into issues where iOS is caching the handles. I found out that I need to set IS_SRVC_CHANGED_CHARACT_PRESENT to 1.
But where should I do that? In sdk_config...
Currently messing with the NRF52840 chip and given examples (NRF Connect SDK v1.7.0) on two different eval boards (the nRF52840-DK from Nordic and the BMD 340 Eval board from...
