I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm having some troubles with the Thingy:91 because it became unresponsive after I flashed the device with the mqtt_sample firmware.
I built the mqtt_sample with...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). So far I had been using ncs v1.6.0-rc2 during development. Recently...
hi support team，
customer have one question, when 9160 attach the network, which one does it choose (the best signal or the first base tower discovered)?
especially when...
Hi Dev Team,
I am developing the weight scale product using nrf52840 development board. We connected the nrf52840 using the nrf connect app ( Provided by nordic).
Now...
Hi, I'm using the BC805M EK (nRF52805) . I would like to pull up pin 20. Here is my configuration in pca10040.h. However, pin20 cannot be pulled up. It's always pulled down...
Hello Devzone Community,
I am trying to develop an nRF9160 firmware, based on Nordic's sdk-nrf v1.6.1 code base. This work is a Zephyr RTOS based application. In early research...
Hi, I would like to know all of my possible options for improving the communication range between 2 nodes in ble mesh. I am working with the nrf5 17.0.2 SDK and the nrf5 SDK...
Hi everyone,
Explaning my project: an external device transmit via UART to nordik nrf52840DK device with UART peripheal firmware, this is connected to another nrf52840DK...
I'm testing the http functionality. In my code I test against 2 different servers, one plain http port 80 "postman-echo.com/post" The second server is private https server...
We are using NRF52832 with STM32L4A6 using serialization. We have the serialization working properly, but having an issue with the MAX MTU size. We can set the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hi, I recently started working with Segger on nRF52832 . It is possible for me to initialize BLE advertising but I am having problems in initializing a custom service. I ...
Hi,
I am currently working on a project that uses the nRF52840 MCU implemented with the nRF5 SDK and nRF Bluetooth mesh. In our future plans, we want to use direction...
Hi There,
I am trying to generate build files for unit tests according to nRF5 SDK for Mesh v5.0.0. It could succeed. I try everything, it still cannot work. (In windows...
I am trying to use SST26VF064B IC in my project (We use nrf-sdk-16 ). we use a driver code that was already tried and tested with the stm32 controller. But when trying to...
