I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have been trying to install the latest version of "nrfConnect for Desktop" on my Mac. I am using latest macOS (Big Sur v11.5.1) on and Intel-based MacBook Pro.
When I...
Hi,
I am unable to locate the list of error codes , in my code I get "sd_ble_gap_scan_start returned 0x10" as I use sd_ble_gap_scan_start() function with input parameters...
Hello,
I am trying to program and use the AWS IoT example to send data to the amazon webserver. I worked through this post ( https://devzone.nordicsemi.com/nordic/cellular...
Hi,
I am designing a module based on the nRF52805 and wonder if there are also GPIOs that should not drive high frquency, like stated here for the nRF52832:
https://infocenter...
Hello,
Is the MBEDTLS_USE_PSA_CRYPTO functionality supported in nRF SDK 1.6.0 (nRF9160)? Setting this value in Kconfig doesn't seem to propagate to nrf-config.h.
If I...
Hello,
I want to transmit data gain from an i2C sensor from one nRF52832 to another via BLE.
I have successfully configured i2C and now I can store those values to Variables...
Is it possible to get the PPK2 to return the voltage VDUT+ (VDUT_SENSE) instead of the current when taking a measurement?
if so what is the command?
Thanks,
Mar...
Hello all,
There is a strange case where a custom board with nRF52840 is able to connect to JLinkExe on a Linux machine with the JLink debugger present in nRF52840 DK but...
Protocal :ESB
Devices : 1:central(PTX) 2:peripheral(PRX)
Description:
1、Central transmits data to Peripheral,and then Central receives respond data from Peripheral ...
Hello,
myself and my team are evaluating the use of Nordic Connect SDK offering on nRF52840-based board.
From what I understood, aside from the open source and common...
I have an OTA issue with Galaxy Note 10.
During OTA, phone transmit an odd packet, abnormal offset and some overlapping data.
in debugging, i got to see the abnormal...
Hi,
For our application we need time and date updates from a mobile phone. Bluetooth has a standard Current Time Service for this. However I can't find this service in the...
I use two nrf5340dks to run the routines in NCS \ v1.5.0 \ NRF \ samples \ ESB; The distance between the two nrf5340dks is only 10cm. When the transmission interval is set...
Hi, I'm programming both Central and Peripheral.
[Picture 1] is what I want to implement.
[Picture 1]
Central connect multiple peripherals which is the same functionality...
