I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hey there!
I am currently in the process of building a module that drives a high-res OLED display using QSPI. Until now I've used a RP2350 with PIO and DMA for this and...
Hi everyone,
I AM LOOKING TO HIRE SOMEONE TO HELP ME WITH THIS OVER A ZOOM SESSION ASAP. PLEASE DO READ ON IF YOU CONSIDER YOURSELF SEASONED/KNOWLEDGEABLE IN THIS AREA....
Hi Team.
NCS: 3.0.1
Board: nRF54L15DK
I am adding a custom attribute of struct data type into the standard Occupancy Sensing cluster (0x0406) in matter template sample...
Hi,
we are confused:
The PS of the 9160 has the single Note: The LTE modem requires use of LFXO as the LFCLK source .
But looking at the reference schematics for the...
I have tried the following to no avail.
Tried 2 different laptops of Windows 11 with 2 different USB cables.
Tried ext power supply at 3 volts with SW10 set on.
Set...
HI
I am currently using NRF54L15 with SDK version 3.0.0, and I want to implement GRTC auto-reload without using interrupts. My main goal is to reduce CPU usage and utilize...
When programming my NRF52832 target card with VScode, if I don't use debug play, the code doesn't execute. What could be the reason? I don't have this problem in Segger Studio...
Hello:
I was using VS Code normally. Suddenly, I opened a folder and received the screen below when selecting nRF Connect. Note that no information appears. Line 7 of the...
Hi,
Today I have received nRF54L15 DK from Digikey UK and planning to connect a low power VGA camera for a mobile application over BLE. Do you have any recommendations...
I am currently debugging the nrf52832 project developed using the nrf5SDK.
I will encounter SOFTDEVICE: ASSERTION FAILED from time to time, like this:
I don't have a...
Hello,
I know this is a documented error but I'm still struggling to fully understand and fix this.
Context:
I'm trying to make my custom display driver working again...
Hi~
I'm using an nRF52 DK connected to the nRF54L05 with jumper wires for the flashing operation. I've confirmed that the DK works correctly, as it can successfully program...
hi support team,
customer is preparing to use 21540, only use gpio mode, not using spi interface,
may i ask how to deal with spi pins of 21540, float or pull up to vdd...
Hi,
I'm having trouble with the Matter Test Harness randomly failing tests and failing to commission my device. I have tried this with both my own Matter device and the...
