I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
why doesn't the mesh chat example work on nrf5340?
I know it's not included in the list of supported platforms, but I'm trying to figure out why.
I can compile and upload...
Hi,
I've noticed that when I'm not initialize BLE stack, I have a failure in nrf_sdh_soc_evts_poll function (NRF_ERROR_NOT_FOUND).
Can you please explain what is the reason...
Hello:
nrf_pwr_mngt_run() doesn't always work on my custom board. About 1 time in 3, in code (I'm running in debug mode and using RTT) spits out
ERROR 3735928559 [Unknown...
Hi. I flash a board with NRF51822 via SWD pads, and that way the push button is inaccessible, and I need to press it to test various functions. Push button is on 28 bit and...
Hello,
I am using the n RF Connect SDK v1.5.1 and using the Zigbee Projects.
I wanted to know if and how to change the default stack profile of the Zigbee App. The following...
Hi! I am trying to interface the CCS811 with the nRF91-DK. For this purpose I am using nrf-sdk 1.6.0 and "ccs811" sample from zephyr. I created a nrf9160dk_nrf9160ns.overlay...
Hello,
I developed a code for nRF52840 Dongle to publish data on mqtt-sn topics (I'm currently using Nordic SDK for Thread and Zigbee). I need to know what are the limitations...
I'm working from the https://github.com/Martinsbl/nrf5-mpu-examples/tree/sdk13/nrf52-mpu-easydma-using-gpiote-and-registers example and the DMA portion is working splendidly...
I am trying to build the nRF Connect SDK project "at_client" that is provided with the IDE. I also tried the asset_tracker project with a similiar result.
This is my first...
i use a thread to save fil like below ,and find can not save file in sd card ,sd card SPI test ok . before enter in loop. close fil and reset system can save fil in sd card...
The first bug : I believe that the target level argument for the definition of the transition callback should be of type int16_t instead of the unsigned version since it is...
I'm trying to add a sensor driver to my project based off of Zephyr's sensor driver for adxl372. I can't figure out how to get the Kconfig file in that sensor folder to show...
Hi Nordic team,
I'm struggling with an issue where my chip wakes immediately after calling sd_app_evt_wait() - specifically if I call app_timer_start() before the wait for...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
