I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
Is clearing the NRF_UART_EVENT_RXDRDY really sufficient before exiting the IRQ handler? Since Cortex M4 is used, there's no need to clear the pending register (to avoid the...
Hi, Could you pls check, is it ok if these logs happened?
No firmware defined for selected device Please make sure the device has been programmed with a supported firmware...
Hello
I would like to modify the example "ble_thread_dyn_mtd_coap_cli_nfc" to use Just Works pairing instead of OOB with NFC.
To do this, I modified this in sdk_config...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
So I'm trying to get to grips with the ble_app_blinky example from nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky
To start with I grabbed the hex file ble_app_blinky_pca10059_s140...
Hi, 1. In ncs v1.5.0 nRF5340 I need to drive a spi peripheral w25q128 2. How do I generate this file?
3. Where can I find the syntax rules that generated this file? 4. Can...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
Hi,
I have a custom board with nrf52840 with UARTE1 instance enabled for RS485 communication.
I have 2 boards on the same configuration and trying to send data to each...
Hello,
I am trying to use a nRF52840 Dongle to perform DFU over Thread: I am using a PCA10059 board, already provided with the default bootloader. I also programmed the...
Hello,
I am in a project using nRF52 board where I develop and Android app.
The application is using Android stock BLuetoothLeScanner to scan for devices. After that the...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. This bonding information is written to the flash area using...
So...I have an idle task running then a UART interrupt fires upon a character being sent over the serial, and somewhere during the execution of the ISR, it attempts to execute...
