Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I want to use a MPU6050 sensor with my nrf52832 board.
I connected the SDA and SCL pins of my sensor board with the pins P0.26 and P0.27 of my nrf52832 board, respectively...
Hello. I'm working with multilink example and I've got some problem. I want to send data to specific peer device, but after restart central or one of the peer, they reconnects...
Hi. I have a problem with Segger Embedded Studio. I always get more than 100% of RAM usage when building project on SES, even if examples projects from SDK . Anyone know what...
Hello, I have the following question. I'm trying to program my firmware via DFU Bootloader and nRF Connect (smartphone). That works perfectly with the test board SparkFun...
Hi,
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Hi, After updating my nrfConnect to 3.6.1, I had issues using my J-link being unrecognized in the programmer app. The J-link I'm using is part of a Silicon Labs Dev Kit, checking...
Hi, I was wondering if there are any problems with connecting VDD to an external power supply when using nrf52840 in the high voltage mode? I would like to connect VDDH to...
Dears,
1.I want to know when working at USB CDC mode, what's the phy rate could be supported? And what's real rate is it？
2.Could customer customized their private protocol...
Hi,
I've read that highly secured IoT devices have a hardware root of trust. One very important feature of it is a private identity keys to prove identities for mutual authentication...
Hi,
I noticed at least using pwr_mgmt we are calling two times nrf_pwr_mgmt_run for every interrupts ! All interrupt seems to be triggered twice ! Or wakes from idle state...
HI Nordic
I currently have a 2 separate projects, that i'm trying to merge.
- Production test tool with RTT CLI interface on nRF52840 (Here I use JLink.exe -device NRF52840_XXAA...
Hi Nordic teams,
I'm developing the function of Mesh DFU. I've test the nrfutil tool locate on https://github.com/NordicSemiconductor/pc-nrfutil/tree/mesh_dfu , and it works...
Hi All,
I have designed one device using nRF52840 MCU and software SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
From Software end all features are implement and...
Hi Sir,
As check nwp_024_v1.6.pdf, it only shows the tape real information w/ below series.
nRF24
nRF51
nRF52
nRF8000
nRF9160
I don't find the information for...
Hi,
I have a SPI peripheral connected to the nRF960 DK. In order to access this correctly, I need to be able to write a byte to a specific address first and then read back...
