We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi community ! I saw a lot of subject about "Mesh throughput" which was outdated and i still have questions. I'm using nRF52840 DK with nRF5 SDK for Mesh v4.0.0
1) Does...
Hi,
I'm using nRF Connect to connect to the secure bootloader. In the debug log I see that an MTU of 185 is requested and 183 is replied. I also see this in the Wireshark...
When I used nrf52840 to connect the peripherals with pc-ble-driver-py, I had my own custom UUID, so I needed to add a custom UUID. I referred to this article , but the following...
Hi,
I know that there are different ways to set up the radio, but generally speaking, is there a general practice for how commercial devices' PHYs are set up when advertising...
Hello people, Honestly this is a problem more related to a Raspberry Pi than the nRF52832 but I'm getting same difficulties here so I will explain my situation. I have been...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
Our hardware has Winbond NAND Flash chip connected to the nordic MCU(nrf52840 /nrf5340). However QSPI cannot be used as nordicSDK doesn't support NAND Flash.
I understand...
Hello,
I am using the Power Profiler Kit connected on top of an NRF52840-DK
I am using IAR and using IAR's J-LINK plugin to program/debug an application on the DK. However...
I am trying the example project ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\l ight_switch' and ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\ dimming' available in nrf5_SDK_for_Mesh_v4...
