I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I got an error 8(NRF_ERROR_INVALID_STATE) while running ble_nus_c_tx_notif_enble function.
The SDK document shows that, the err_code is
"this API propagates the...
I'm evaluating using zephyr for an nRF52840 based design. I'm able to use the nrfx drivers via Kconfig options. It doesn't appear that there any other Nordic SDK libraries...
Hello developers.
I successfully ran the Mesh project with Light Switch example on nRF52840 devices. And I have 2 questions about this.
Question 1: How can I access from...
Hi.
I'd uesd RTT viewer before SES.
RTT viewer has the menu for saving logs.
I'm a new for SES. I'm recently using SES.
I can see log message on SES, but I don't know...
Hi,
I am just unable to find the FW ID for SD v7.2.0 anywhere.
I am using SDK 17 and s140 7.2.0 and am trying to create a DFU package to update both the Soft Device...
Hello All,
We are testing power consumption nRF52810 in system ON mode , my configurations as below,
Device will advertise for 10 sec connect with the mobile app sends...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
