Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I've been using XMONITOR command to check some radio parameters. ATM, I am checking those once/minute, right before requesting power save mode from modem. After updating...
Hello,
I wondering if I use the nrf5_SDK_for_Mesh_v4.2.0_src light switch example and modify it to suit my needs.
Q1. I want set up a proxy node using nRF52832 so that...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
Hello,
I am trying to use "west" command in Eclipse but I am not able to do it.
I was able to do that in Visual Studio though.
I found this link https://devzone.nordicsemi...
Hi,
We are trying to configure the WDT and are running into issues. The plan was have a timeout of 30 seconds when running and then 24 hours when sleeping. Note we are...
While developing the power supply for edge cases of NRF9160-SIBA we encountered problems with both the continuous and peak current consumption, mostly during startup. We are...
I have a question on stack guard that I tried to enable on nRF52840 and hope you can give me some pointer to verify it is functioning properly.
Basically, I call nrf_stack_guard_init...
Hello i am making an application using hid over gatt. i changed original keyboard usb description with fido description for test, however, i don't get any event through. I...
the link i given below tells, how to make a haptic glove using arduino mega
https://hackaday.io/project/160405-diy-haptic-glove-for-vr
i want to do it with nrf52840 DK...
Hi everyone,
I'm working on programming nRF52833. I want to my nRF52833 is able to broadcast advertising and also scanning (In another word, my device plays peripheral role...
Hi
I have upgraded from an early version of SLM to the latest version in nRF Connect SDK ver. 1.3.1
the SLM application is running on a custom board with a nRF52840. Using...
I found this application very useful!!
The code is now at the Github.
I found there are some problems to reconnect - it gets many errors and the peripherals eventually...
