Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I have some questions relate to Advertising:and RF ANT:
As I understand about advertising, there are only 3 channels, which can broadcast the advertising, are...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to follow this example.
I connected successfully, but I have problem in 'Advertising' part...
Hello, Support team:)
I wish to use NRF_LOG_DEBUG function in segger embedded studio.
But there is no message in "Debug Terminal".
- nRF SDK 16, "/examples/proprietary_rf...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
UART works normally at 3.3V.
But if I lower the power...
Greetings. I am on a mission to upgrade the BLE Firmware of nRF52840 via UART and ultimately via the UART communication between our main Micro (Microchip PIC) and nrf52840...
Hi,
I am developing a product using nRF52832 . (S132, SDK 17, IAR8)
I am developing based on the ble_app_uart example.
I would like to add a basic PWM code to...
I had some issues with Errata so I tried to build a simple BLE app like Blinky.
The errata functions all compile as return false. For example, nrf52_errata_108
What...
I would like help in understanding the limitations of the NVRAM. The documentation for the nRF52840 and the nRF52832 are different. This is what the nRF52840 reads:
Do...
Hello all,
I am new to BLE mesh programming. I want to develop a multiple sensor client-server model where sensor data (eg. temperature values) from multiples nodes in a...
Setup:
- MESH SDK 4.1.0
- nrf52832.
Consider the following scenario:
- 3 nodes (A/B/C) are provisioned on the same network.
- I'm using a custom model with reliable...
Hi Team,
nRF52840 boards are getting fail continuously not able detect by Host computer.And the boards are no more useful and all boards are brand new only One day we have...
Hi,
I am trying to enable Bootstrap support.
Therefore I set "CONFIG_LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP=y" in prj.conf.
I also set "CONFIG_APP_LWM2M_SERVER" and the port...
I have built boot-loader hex file from SDK 12.1.0 secure DFU project, without any changes except for public_key.c file.
I am referring to steps mentioned under
Combine...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
