Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi ,
I am using NRF52832 device and I am referring ble_central/ble_app_hrs_c app . in this example , there is secure data used(pairing and bonding information) for whitelist...
I would like to create a repo to house all our vendor-specific board support, applications, etc. outside the Nordic nrfConnect repositories as per the Zephyr workflow. However...
Hi, I am an internship student and so new at programming. I have a nRF51822 DK that includes;
2 x nRF51822 module
2 x BLE master dongle
J-Link Cortex emulator (Debugger...
Hello everyone,
We have an IoT device with the nRF52832 module installed. We are in pre-production and in the process of certification. Our laboratory (EMITECH) asks us...
Hello team, i use board nrf52832 and SDK15.3. in example ble_app_uart_c. BLE_NUS_C_EVT_DISCOVERY_COMPLETE event occurs only once, after losing the connection and reconnecting...
Is there an example for setting up a Segger Embedded Studio project for using an nRF52840 with Zephyr. The instructions on the Zephry site for adding Zephyr files to a project...
Hello,
We are currently designing a device that will use the GPS on the nRF9160, our implimentation will involve using sensors to trigger GPS measurements for the duration...
I am using an nRF52832 and the Nordic UART Service (NUS). I am using the example NUS code and the UART side is plugged into another microcontroller's UART. By default that...
I need to find rssi value of my mobile (using nrf blink app) using nrf52840 Dk.. So i generally don't have idea what changes to be made for ble_peripheral->ble_app_blinky...
Looking at different solutions to an asset tracking system I'll be working on as my senior project later this year (getting a head start so time isn't as much of an issue...
Hi,
I'm writing a driver for a Ublox cellular module, which will be communicating with the nRF5240 using UART. After going back and forth, I decided to go with the app_uart...
Hello, I am an intern at a startup company and ive been tasked with finding some information about the chip set we are using, specifically the bluetooth aspects. We are using...
Hello,
I just installed SEGGER Embedded Studio to build the light switch example for Bluetooth mesh.
I managed to successfully follow the quick start guide using 3 development...
Hello!
I managed to flash my Raytac dongle with debugging going using the SWD on a nrf52 DK. I am mainly working with SEGGER Embedded Studio and nRF Connect on Mac. However...
i m getting constant RSSI values 32 even if i move far or near
this is the same example code in ble_peripherals
I HAVE UPDATED MY CODE (i have printed the RSSI values...
