Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi All,
I am Using the NRF52840 DK Device for my application development
I want 2 UARTS for my application
I have used the example - nRF5_SDK_15.3.0_59ac345\examples...
I am currently developing a central device based on the NRF52832. I am able to discover and get handles to all the services and characteristics of interest on the peripheral...
Hello,
I wanted to know if I can use AT commands to communicate with nrf52840 DK.
If it is possible, do I need to have a separate firmware or is nordic sdk enough?
Hi, I am new to FreeRTOS and am planning to change to some of my code routines to FreeRTOS because my code has been expanding and in need of priorities interrupts. I face...
Hi,
I have modified the asset tracking application to work with my AWS IOT account, I have noticed that after several minutes, the broker stops responding (not getting PUBACK...
Hi,
I am experimenting with ENC28J60 and PCA10056. Following are my connections:
================= =================================== NRF52840 PCA10056 ENC28J60 (pin...
Hi
I tried to implement Eddystone example in nRF52810. it worked successfully. Then i tried to implement same in nRF52832 using pca10040. But it not working. I only changed...
Hi, I'm running the saddc_pca10056 peripheral example given in SDK v15.2.0.
The analogue pin A0 is connected to the signal line of an LM35 temperature sensor. When I measure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I am porting RTC example code as is into ble_app_blinky...
hi...
i want to advertise the multi link central example , i have added the advertising in code , now my central is advertising but when i tried to connect , i am getting...
I programmed a NRF52840 Dongle with the example light switch code having changed the channel to 14 which is what my coordinator is on.
I then programmed a NRF52840DK with...
Good day,
I program my nRF52-DK with BLE Eddystone example's pre-compiled hex:
\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_eddystone\hex\ble_app_eddystone_pca10040_s132...
my bootloader.hex is generated by "nRF5_SDK_14.2.0_17b948a\examples\dfu\bootloader_secure_ble\pca10040\arm5_no_packs", my app.hex is generated by a modified blinky example...
