I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I wanted to try the bootloader related example. I was using the IAR to run peripheral examples.
But for bootloader example, I saw that IAR was not listed. So installed the...
I read the following QA - https://devzone.nordicsemi.com/f/nordic-q-a/41237/on-dfu-jump-address but still have doubts
1. Is it safe to set the Bootloader RAM start address...
Hi,
Hardware：nRF52840 module, Power Profile Kit. SDK：nRF5_SDK_15.2.0_9412b96.
Using Power Profile Kit to measure the low power consumption current of an nRF52840 product...
Hi,
I am currently trying to use SDK 15.3 secure serial UART bootloader (from the example in nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart) on a custom...
hi, I am working on the bootloader with s132.5.0.0 on sdk14.2.0. I am trying to using the uart to flash the chip.
I build the bootload example bootloader_secure_serial,...
I'm using three PCA10056 boards to test mesh example(Meshv3.1\light_switch).
[light_switch_client] ---> [light_switch_server1] ---> [light_switch_server2]
*Put the server2...
I am testing a mesh network, using the NRF52832 modules, SDK 15.2 and MESH_SDK 3.0, provisioning the nodes with nRF Mesh android app and using a modified firmware for the...
I am trying to build UART support into my current project but the compilation of the nrfx uart driver fails. See error below:
Any idea how to solve this? Is there good guide...
Hi,
I'm using the NRF52840 with the "nRF5_SDK_for_Thread_and_Zigbee_2.0.0".
I tested the zigbee light_bulb example and zigbee light_bulb + ble. It works fine so my next...
I'm trying to extend the light_switch client example (from mesh SDK 3.1.0) to a gateway. The gateway will consists of nRF52832 and a WiFi module connected via serial interface...
As the title descripes i get an error with a file name in it but i can not locate this file.
I am working with the 802.15.4 wireless uart example on a nRF52840 DK. I only...
All nRF52832 based RF modules on the market have been certified using a Nordic SoftDevice. Some manufacturers say that it is ok to use a different Nordic SoftDevice without...
Hi I have been put into at task with a nrf52832 device (Mesh) that can only update the application. This is a big problem because we already have multiple device all over...
Hello. We are using nrf52840 for our product and I wanted to use aes ccm encryption for security. I was able to integrate CC310 library but I found out that encryption works...
i'm working on dynamic multiprotocol between ble and thread.
i want to ask about ble packet size in link layer and how could i change packet size ? is it could affect loss...
