Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
If an ESB PRX has queued a 250-byte auto-ack payload, that will take around 2ms at 1Mbs to transmit.
If the ESB PTX has the standard 250us repeat interval, will the...
I am confused about the value of RX_PW_Px register what will be the value of this register if more than 1 dynamic payload packet arrives on the same pipe-x.
I'm a beginner I'm having hard time understanding UART. In my opinion, the documentation is going too straight to the technical details and tutorials without even starting...
Dear friends,
Is there any ideas for measuring the distance between a BLE module and a beacon module without using RSSI?
With Regards,
Sunil
Calixto Systems
hi..........
i have developed nRF52832 QFAA using your schematics,and i have added sensor to it . Now i can able to flash the code and ran successful but i can't able to...
Hi,
We are developping a system connected to several devices based on NR52 MCU.
The DFU works with the nRF connect application.
Now, we would like to update the device...
Hi,
I am just getting started with the thingy 52 and I need some guidance. I am a EE by profession so I feel a bit out of my league here.
When I unwrapped my thingy I...
Hi there,
I am adding security to my service characteristic and i found that for security mode 1 level 4, bonding is required in order to access characteristic values. Is...
Hello,
My problem is pretty much identical to this one:
devzone.nordicsemi.com/.../
My functions look exactly like the ones posted in the original question and I...
Hello, and thanks for all the great examples!
I've gotten the COAP transport for background DFU working on my custom hardware platform and app, however I have noticed that...
Hi,
I do have a NRF51-DK and want to use it as a external programmer. I connected it to the OUTPUT Port which worked fine, then I flashed the mbed firmware on it because...
Hello,.
I have a question about using app_usbd_cdc_acm_read and app_usbd_cdc_acm_read_any in SDK15.2.0,
I am not sure I fully understand the description in reference...
nRF52832, SDK 14.0.0, SoftDevice 132 v5.
If SoftDevice is enabled but the system is not yet advertising or connected via BLE, will SoftDevice ever wake the CPU up from...
Although redirect.c is included and printf() calls use the uart as expected, fgets() calls don't seem to be able to detect incoming characters.
This isn't critical, since...
