Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
In iOS, I have developed one sample code for BLE scanning and connection with peripheral.
I have one nRF51822 Ble. It has secure pairing mechanism. (Claimed by Hardware...
nRF52, SDK15, S132
Hi! After few days work I have stop scan from my central device on the nRF52832.
I can't to understand reason of this. But I need to know is scanning...
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this bootloader code install...
Are there example scripts to take readings or communicate with other devices over serial? Like, if I attach a temperature sensor, distance sensor, etc, I want to read from...
Hi there
I was going through the errata sheet and discovered the PAN #88.
It states that the current consumption is increased when entering System ON Idle within 125us...
If I just comment-out battery_measurement_init() in main():
Advertising does not start, I see nothing on the UART CLI, and the RTT log just shows:
With battery_measurement_init...
All examples shipped with the SDK have the same compile problem
components\libraries\util\app_error_handler_keil.c(47): error: A1198E: Unknown operand
The offending line...
Hi to all,
i had developed an app for PCA10056 and now i want port it on PCA10059, there is any guide or white paper that indicate how can i done that??
i read in the...
I've just started evaluating the nRF52840 DK and running into an issue when attempting to run any of the multiprotocol ble_thread examples.
I've downloaded the "nRF5 SDK...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
What is the intention of the LOCKDETECT field in the FIELDPRESENT register? I don't understand the description...
I can't connect to my nRF528540-DK anymore after I connected an external power supply and switched SW10 to off. the external power supply is 5V. my DK doesn't show up in device...
Hi
I open the SAADC to get the battery after initial the SAADC, using nrf_drv_saadc_sample_convert to get the ADC data . After nRF52832 is initialed, it enter power_manage...
Hello I'm using a nRF52810. Now i'm trying to add an PCB antenna to my Altium sheet i Wrote in another Reply that i could use the one from your USB Dongle but i don't find...
Hi there,
I need realtime data monitor, but the power consumption is too large when BLE sending data continusly. So I wanna know wheather NRF52832 support package the...
