I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm trying to implement the workaround for PAN58 on an nRF52832 device using SDK15.2
I've copied in the code from a previous post but I keep getting an error when I declare...
Hi, I just finished prototype using nrf51822. I programmed my part while it's mounted on my PCB.
I am preparing for mass production. So I need to program the parts quickly...
nrf52832 mesh lpn power consumption is too high when enabled MESH_FEATURE_PB_ADV_ENABLED,
when provisioned completion, power consumption is still very high, Restart the...
Hi,
I am relatively new to C coding, and need to use the NRF52832 for a school project. I need to write a program that measures frequency from a GPIO pin. From what I've...
Hi ,
Our customer use nRF52832 to design the mouse. Currently they had problem to do the connection with Lenovo T470 after power cycling (POWER OFF and Then POWER ON)...
Hi:
I want to transplant nRF52840 pca10056 driver, where is the driver file of nRF52840 pca10056. How to transplant? Is the source code all public?
THANK YOU!
Dear All,
I'm willing to set up a project based on the nRF9160, using the Trustzone. Thus, I have two firmwares, two zephyrs that will run in Secure and Non Secure memories...
Hi:
I use sdk15.3,usb pca10056.
nRF5_SDK_15.3.0_59ac345\examples\peripheral\usbd_ble_uart_freertos transplantation to ble_app_multilink_central.
this is log:
<debug...
Hi, I'm trying to implement DFU over BLE using nrfutil in a product. The product(will refer to as peripheral from this point onwards) also has a dongle(supports flow control...
Hello,
For a project I am currently working on I am trying to track patients' movement through a hospital clinic. To do this, I plan on having mobile NRF52 DK boards traveling...
Hi
How many bytes of data can be written to flash memory at a time? I am trying to write an array of 10 elements of 16 bit data type , but only the first four elements are...
Hi,
I was wondering if a central can perform multiple read requests with authorization, i.e. send a read request before it has received the reply to the previous request...
Hi,
the system we are using includes the nrf52832 SoC with an external ADC and en external crystal for HFCLK. running SoftDevice s132 v2 (based on SDK 11)
in our system...
I like to program NRF52840 Dongle without using NRF Connect Desktop (i.e, Normally we develop application program using some IDE) Can i develop application program using NRF52840...
