Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
When building a project that compiles the hal_nfc_t2t.c, it errors for nRF52840, but works for nRF52832.
For the nRF52840, I get these errors:
Looking for some of the...
Hello, I want to transfer a large file (approx. 1.5MB) over BLE using nRF52 Module in a way where BLE Host and BLE Controller will be on the nRF52 SoC and the application...
I added ams service to my project, and I tested with my iphone 7P, seems all goes well. But today I tested with my iphone 5S, sometimes the hardfault exception raise.
Hi Nordic,
I'm trying to use a nrf52832 dev kit (v1.1.1) with NRF Connect (v2.5.0 on mac) to communicate to my device (NRF52832). My device has implemented MTU exchange...
Is there something on the specifications regarding the structure of a node? We have a node currently with 3 Elements:
El0: Light controller: Config model, Health model,...
Dear Sir,
I am using SDK15. Softdevice s 132, and nrf52832.
I was working with code 'ble_app_template'.
I was trying to find out the transmit power set for the...
I am trying to create a datalogger onto a uSD card with a fat file system. I have been able to run the fatfs example which creates a file on the uSD card, NORDIC.TXT. The...
Hello
We have a double problem, the CPU wake up doesn't work, but the sensor who wake up the CPU is correctly configured ant the interrupt pin go low to high when the temperature...
Hi Sir
We plan to implement our own DFU controller on host MCU to upgrade on board DFU module by UART.
Zip file will be generated by nrfutil and saved on flash.
Can...
Hi,
We've developed a BLE HID device with mouse and keyboard capabilities based on the nRF52832 and SDK 14.0.
We're interested in declaring the CoD as " Combo keyboard...
SDK : nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac
segger studio
I merged uart peripheral into simple coap clinet example
this is errors:
Output/Release/Exe/thread_simple_coap_client_pca10056...
I have the USB Dongle (PCA10059) which after a full erase, has been giving only 1.8Volts to the GPIOs and the VDD OUT pin.
I am using the Segger j-link EDU progammer/debugger...
Hello Community,
I am looking for some assistance in getting my nrf9160 DK to connect.
I am running the AT_Client sample and LTE Link Monitor. I am in Toronto, Ontario...
