Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I'm trying to make i2s working on mbed os by using NRF52 development kit board (based on nrf52832).
Looks like I'm missing something. What I managed to do so far is:
...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
HI,
I am working on NRF52832 SOC. with SDK 15. where i need to read the SENSOR data from twi protocol.
Common Write and Read Register function has been created
I...
Hi,
I would like to use the Raspberry Pi and the Thingy:52 as published in the demo. My question is, how many Thingy:52 devices are supported by the demo?
I have a nrf9160dk I followed the steps in the movie www.nordicsemi.com/.../GetStarted I have inserted my own sim that is working in my phone but I do not get LED3 and LED4...
Hi There
Is there any additional drivers that i have to install to use nRF connect on my Mac?
I've installed it and when i connect the nRF9160 DK to the Mac, it doesn...
Hi, I am trying to implement app_timer library with FreeRTOS. Based on my testings, it seems that app_timer_start() under app_timer_freertos.c has the lowest time resolution...
Good day
I moved from Mesh3.00 to mesh 3.1 and I see the way UUID is extracted is slightly different.
I would like to know when I copy the UUID to use in my project will...
Sorry for disturbing!
I have some questions about measuring nRF52832 32Mhz Crystal frequency.
I use an active probe(Tektronix P6243) to catch the signal and the test result...
In the case where connecting to a phone that is paired with my device after my device has cleared pairing information and doesn't remember the pair, I'm observing the following...
I'm working on a project to get two devices to agree on a secret key based off of physical layer properties.
My solution is for devices A and B to make 64 RSSI measurements...
Hello, we have developed our product with S132 version 6.0.0 and sdk 15.0.0 since that was the most current when we were in the development stage.
However, now we need the...
When switching the dongle into DFU mode, it changes the serial port number when running in windows.
Both the bootloader and the application sets up the USB and calls the...
Hello, I am using the nRF51422 development kit. The SDK I am using is the nRF5_12.3.0_d7731ad. I am trying to run the "Blinky" example by copying the hex file for the PCA10028...
