Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi Every one,
I am trying to use two uart's communications concurrently in nrf51422, in my code i am running timer of one second.
Every one second in timer routine trying...
hi....
i am using nrf52382 and segger 15.2 version , i want my peripheral to send the data only if it reaches the certain limit (threshold value) on that case it should...
hello , friends
i am using nrf52832 ,debugged the ble uart program ,and then i tried to connect my device over ble uart app,i couldn't found my device ,then i tried to connect...
Good morning!
First of all, the background. I made a custom board and programmed it, everything worked like a charm. After that, I made another one, same hardware, same...
In my previous question , where I wanted to atomically send a large bulk of data, the solution was to keep track of p_bus-> free_buffers , in order to calculate the amount...
Hi,
I’m using SDK 15.00 and I have some issues with NFC. When I’m trying to connect with NFC - NFC_T2T_EVENT_FIELD_ON event occurs. At this point, I need to start BLE...
The release notes for S132 v6.1.1 lists a bug fix:
"Fixed an issue where NRF_TIMER0 may not be reset at the start of a radio timeslot (DRGN-10650)."
Did this bug exist...
Hi,
Here and here are examples of a port of the nice u8glib library to stm32. Based on these, i tried a port to nrf52, but was not successful so far.
I call the oled...
I am trying to save data to the flash memory. My starting file is the ble_app_uart_pca10040 (s132). I am using the sd_flash_write address is 0x007ffd0 and a value of 0; I...
We have developed a custom board using Raytac MDBT50Q with NRF52840. It has an external EEPROM and a RTC. We made an app that we use to program 4 daily alarms through BLE...
nRF51822-EK page is no longer available on the website. By any change I can get the PCA10001 schematic somewhere?
I would like to run some conductive RF testing and would...
Hi,
I recently moved a project from Mesh SDK v2.2.0 over to v3.1.0. I read the release notes and saw that there have been some changes to the Flash Manager module.
During...
I need to include in my project Advertising, buttons and battery power measurement.
I am using SDK 15.2
If I get ble_apps_bps and include advertising functionality (from...
